Версия для печати темы

Нажмите сюда для просмотра этой темы в обычном формате

Клуб Любителей Mazda Demio _ Автозвук & Электроника (1996-2002) _ програмирование брелка

Автор: Rama13 29.4.2013, 19:21

Можно ли как то прописать брелок?есть ли схема?и можно ли прописать не родной брелок а от другой машины

Автор: maxpavel 29.4.2013, 21:03

Проще и дешевле сигналку поставить.

Автор: nait140 30.4.2013, 4:43

Цитата:
(maxpavel @ 30.4.2013, 1:03) *
Проще и дешевле сигналку поставить.


Полностью согласен, Вы пытаетесь модернизировать устаревшую систему защиты.

Установите новую и по дороже, спать будете спокойней wink.gif

Автор: Anton59 7.5.2013, 9:17

прописывание брелка

1. Open driver's door.
2. Turn ignition key to ON (not to ACC as some instructions may state).
3. Turn key back off and REMOVE KEY COMPLETELY from ignition.
Do this two more times, removing key completely each time. Do NOT put key back into ignition
after third time. Keep it in your hand.
4. Press light switch button at lower back corner of driver's door jam THREE times, making sure
that inside lights flicker on and off. (This switch is under the soft black rubber cover. Some
instructions say to open and close driver's door three times which should have the same effect
but never did for me. Pushing the button did do the trick).
5. Wait a few seconds and the car should chime. It might take several seconds before you get
the chime, same chime that indicates door open with key in ignition or seat belt is not fastened.
6. Press the LOCK button on the remote being programmed TWICE.
Wait for the chime again and when you hear it press the LOCK button on the other remotes
TWICE. It may take several seconds but you should hear the chime, probably several chimes.
After this final chime, test all remotes for proper function. These remotes work far better than
any other remotes I have owned over the years.
You can program up to 4 remotes total according to Mazda.
If the above still does not work then lock all 4 doors with the master door lock button on driver's
door. Unlock only the driver's door with the single door button, leaving the other three doors
locked. Swing open driver's door and then proceed as above.


Автор: maxpavel 7.5.2013, 14:14

Это от какой мазды

Автор: Anton59 7.5.2013, 15:38

С Миленьки, но принцип действия блоков ЦЗ Мазды скорее всего один. Кстати есть брелок ЦЗ от Демио2.

Автор: maxpavel 7.5.2013, 22:34

Попробовать можно, а вдруг.

Автор: Vagan 2.7.2013, 10:01

У меня штатный брелок на 240,4 Мгц. А у других авто и сигналок, как правило, 315 и 490 Мгц. Тоже хотел подобрать и не нашел.

Автор: Rama13 2.7.2013, 15:14

Цитата:
(Anton59 @ 7.5.2013, 10:17) *
прописывание брелка

1. Open driver's door.
2. Turn ignition key to ON (not to ACC as some instructions may state).
3. Turn key back off and REMOVE KEY COMPLETELY from ignition.
Do this two more times, removing key completely each time. Do NOT put key back into ignition
after third time. Keep it in your hand.
4. Press light switch button at lower back corner of driver's door jam THREE times, making sure
that inside lights flicker on and off. (This switch is under the soft black rubber cover. Some
instructions say to open and close driver's door three times which should have the same effect
but never did for me. Pushing the button did do the trick).
5. Wait a few seconds and the car should chime. It might take several seconds before you get
the chime, same chime that indicates door open with key in ignition or seat belt is not fastened.
6. Press the LOCK button on the remote being programmed TWICE.
Wait for the chime again and when you hear it press the LOCK button on the other remotes
TWICE. It may take several seconds but you should hear the chime, probably several chimes.
After this final chime, test all remotes for proper function. These remotes work far better than
any other remotes I have owned over the years.
You can program up to 4 remotes total according to Mazda.
If the above still does not work then lock all 4 doors with the master door lock button on driver's
door. Unlock only the driver's door with the single door button, leaving the other three doors
locked. Swing open driver's door and then proceed as above.


а на русском нет?а то переводчик какую то белиберду пишет

Автор: Anton59 4.7.2013, 14:51

Цитата:
(Rama13 @ 2.7.2013, 18:14) *
а на русском нет?а то переводчик какую то белиберду пишет




Автор: Voldate 14.3.2014, 16:28

Кто-нибудь регистрировал брелок на дорестайле? Пытался разными способами с форума - в режим регистрации никак не входит sad.gif

Автор: Dani 14.3.2014, 18:23

Цитата:
(Voldate @ 14.3.2014, 21:28) *
Кто-нибудь регистрировал брелок на дорестайле? Пытался разными способами с форума - в режим регистрации никак не входит sad.gif

Здравствуйте!
Только как пища для ума, у меня так было. Проверьте концевик водительской двери на обрыв провода. ЦЗ при этом работать не будет. И самое смешное - в режим регистрации не войдет!

Автор: Voldate 15.3.2014, 10:00

Цитата:
(Dani @ 14.3.2014, 19:23) *
Здравствуйте!
Только как пища для ума, у меня так было. Проверьте концевик водительской двери на обрыв провода. ЦЗ при этом работать не будет. И самое смешное - в режим регистрации не войдет!

Здравствуйте! Дело в том, что штатный брелок утерян, ЦЗ и ДУ работали исправно.

Автор: Sato 22.3.2015, 18:47

А у меня вообще ситуация, прошлый хозяин оставил 2 ключа один с чипом другой нет, никакого брелка ЦЗ нет, на мой вопрос был ли он мне сказали никто не знает. но подключив Scanmaster программа обнаружила "Дистанционный блок управления дверьми" т.е штатная сигналка всё таки есть... подскажите можно ли эту всю тему восстановить купив брелок и запрограммировать его..
2005 года рестаил
Спасибо.

Форум Invision Power Board (http://nulled.cc)
© Invision Power Services (http://nulled.cc)